Description: Shoretrooper
Prefix: ST
Detachment:PathFinders
Context: Rogue One: A Star Wars Story
Trained and equipped for combat in tropical environments, Shoretroopers patrol the beaches and bunkers of the secret Imperial complex on the planet Scarif.

The following costume components are present and appear as described below.

• Helmet is tan with moderate weathering.
• There is an orange-red circular emblem on the right side of the visor, approximately 3 cm in diameter.
• Visor is trimmed in black along the lower edge.
• Ear covers have one closed recces with 1 large and 1 small raised circle.
• “Hole”pattern snout aerator.
• One recces vent on each side of the aerator.
• 2 wedge shaped recesses on the outer edge of each mandible.
• Rear/side of the helmet has 6 closed recess on each side (total 12).
• Rear bottom helmet lip has 2 long closed recces.
• Two six finned chin greeblies.
• Lenses sufficiently dark enough to obscure the costumer's eyes.
  

• Helmet base color is Sahara Beige.
• Circular emblem matches PANTONE 18-1445 TPX ('Spicy Orange') closely.
• Chin Cup and strap added (hard hat chin strap with cup with 3 oblong cut outs).
• Lenses are curved.
• Second ridge on top of the tear drop that's sits against the lens must be present.
• (Optional) Under the blaster shield and above the lens, there is the black recess curve, at each end there are 3 oblong shaped recess each 5mm x 3mm.
• (Optional)The 6 closed vent slots on each side of the helmet are slightly angled forward towards the face.
• (Optional) Small rectangle recess at the top inner mandibles (optional).
• (Optional)The rear end of the ear plate is slightly angled forward towards the face.

A balaclava is a black head sock/hood that is worn under the helmet and is used primarily to hide any view of the wearer's skin and/or facial hair.

• T he upper n eck seal ribbed section is dark grey, black is a cc e p tab l e .
• Fitted upper neck seal has horizontal ribbing.
• The neck seal bib has vertical ribbing and th e bib is the same colour and material as the undershirt.
  

• The neck seal and bib fitted zip that zips from top to bottom.

• Dark grey ribbed material with Horizontal ribbing on arms and torso.
• Separate shirt and/or separate neck seal with bib(Neck seal is dark grey or black with horizontal ribs. The bib has vertical ribbing and is the same colour and material as the undershirt).
• A neck seal and bib with vertical ribbing attached to the shirt is acceptable. The fitted neck seal and bib must meet the same criteria as the separate neck seal.
  

• The shirt is made from cotton jersey material and has a honeycomb shaped mesh material under the armpit running from the stitch seam and forward towards the chest.
• The neck seal and bib fitted zip that zips from top to bottom.

• Black foam extends past the arm openings.
• Recess on the bottom left must be present and painted black.
• Chest and back plate attach with shoulder straps and meets flush at the lower sides.
• Buckle greeblies attached to upper chest plate.
• Shoulder straps are tan with moderate weathering and are attached to the chest plate at the buckle.
  

• Armour color is Sahara Beige.
• Plastezote is desired for the foam, however plastezote material style is acceptable.
• The shoulder buckle has a slight different shape to the shin buckles. Pin bar closed and not split above the screw, Screw grove is covered and the rear lever bar is longer on length and the curve is slighter and more square than shin buckle.
• (Optional) The Buckles have a 25mm x 10mm x 6mm slot attachment fitted to the front buckle bar.
• (Optional) The Chest plate has a slot recces 27mm x 12 mm x 3mm for the buckles to slot into, the buckle sits 2-3mm above the chest plate.

• Black foam extends past the arm openings.
• Back Plate has a collar that extends upwards and tapers to the chest plate.
• Chest and back plate meet flush at the sides.
• Back has two large cut out recesses with vent details and greeblies inside.
• The walls and floor of the two large recess boxes can be black or dark br own .
• Each recess has different and specific set of black or brown greeblies inside:
  • Left side recess has a rectangle shape greeblie with an angled right side end with 5 panels. The first left panel has a tube on top that then runs up the left side and then across the top of the recces. On the right side a heat sink greeblie is fitted.
  • Right side recess has a long thin strip has 2 flat ends with approximately 17 cylinder shaped teeth in the middle. Below it is a rectangle shape greeblie with a moon shaped end on the right. Approximately 1/3 of the left side is flat followed by a thin line recces and 7x3 rows of oblong shaped indents. On the right side is a circle type hose connector.
• The vent details at the top of the recesses may be cut out and backed with black foam. If they are not cut out they must be painted black in between the slats.
• Bottom left features a smaller rectangle cut out with the left side stepped. The floor of the cut out shall be black and the walls inside match the tan color of the armor.
• Half circle indent detail beneath the backpack section must be present.
• There is a circle recess on the top right hand side.
• There is a long thin raised greeblie positioned central and below the 2 large recess/
• There is a small raised circle greeblie positioned central and below the above named greeblie.
• There is a raised slot on each shoulder for the straps to fit into.
• Shoulder straps are tan with moderate weathering and are affixed to the chest plate at the buckle.
• Back plate is tan with moderate weathering.
  

• Armor base color is Sahara Beige.
• Plastezote is desired for the foam, however plastezote material style is acceptable.
• There is a small circle cut out approximately 5mm in diameter above and to the left hand side corner of the left large recces.
• There are 2 small square cut outs approximately 5mm x 5mm above and to the right hand side of the left large recces.
• There are 2 small rectangle raised greeblies directly above both large recess vents.
• There is a small recces on the bottom right side of the back plate.
• There is a stepped ledge at the bottom of the main back box.
• There is a rectangle shaped line cut recces on the edge of the back plate, positioned halfway down the right side.
• There are 2 small rectangle recess directly behind both raised shoulder strap slots.

• The vertical areas on both sides of the raised center abdomen plate are painted black.
• Inside the right hand black area is a stepped pyramid detail.
• Central ab section has a raised square section with a raised plate, on the left side of the plate is one large ridged rectangle with nine rises ridged below. Above the central section is a double lone rectangle greeblie.
• The left hand black area contains a longer rectangular detail.
• The rear has a central cover plate.
• Abdomen section is tan with moderate weathering.
  

• Armour base color is Sahara Beige.

• The sides have one diagonal raised strip.
• There is a black stripe behind the diagonal raised strip.
  

• Shoulders should be symmetrical with the ridge along the centre of the shoulder bell, this is raised and bevelled.
• Right shoulder is tan with moderate weathering.
• Left shoulder is tan with moderate weathering with one horizontal white stripe, and two smaller black stripes on each side.
  

• The top black stripe is thicker than the bottom black stripe.
• Armour base color is Sahara Beige.
• White, color is Flat white, Matt white.
• Black is Matt Black.

• Bicep cover strips are raised and beveled with a added strip layer on top.
• Left bicep is tan with moderate weathering.
• Right bicep armor is painted red with three yellow rectangu lar stripes on the cover strip, with moderate weathering.
  

• Armour base color is Sahara Beige.
• Right Bicep Red color is Toyota Red 3E5.
• Yellow color is Flat yellow.

• Forearm cover strips are raised and beveled with a added strip layer on top.
• Raised section with a hard corner. Contains twelve recessed areas.
• Forearm may be shortened due to height restrictions.
• Forearms are tan with moderate weathering.
  

• Armour base color is Sahara Beige.

• Black gloves with black leather or leather-like material on the palm, thumb, and forefinger. The palm has 5 raised padded sections.
• The black oval detail is aligned with the index finger of each hand.
• Gloves extend underneath the forearm armor.
• Hand plates are tan with moderate weathering.
• Roughly pentagonal in shape, with an oblong recess on the front edge. The hand plates are mounted securely over the back of the g loves.
  

• Armour color is Sahara beige

• Belt is brown and made from two nylon straps sewn together with a zig-zag stitch pattern down the middle. The belt width is approximately 3 inches (7.6 cm ) wide.
• Belt features: Three standard drop boxes. One extended drop box. Two medium boxes with top detail. Two small boxes with no detail.
• Boxes are tan with moderate weathering.
  

• Drop boxes and Buckle base color is Sahara Beige.
• Long drop box is hinged

• Each part of the assembly is attached to a belt cover plate the same width as the belt.
• Assembly consists of a one horizontal thermal detonator can, a vertical thermal detonator can and one standard drop box.
• The horizontal thermal detonator is a circular canister with evenly spaced grooves extending to the end caps. The end caps have a recess on the top.
• Second vertical thermal detonator canister. Fixed to the left side of the standard thermal detonator. Webbing the same color as the belt, wraps around the canister. Recessed on top and bottom sections. Top recess features a greeblie detail painted silver.
• One standard dropbox on the right side of the thermal detonator.
• All pieces are tan with moderate weathering.
  

• Armour plate, Detonator and Drop Box base color is Sahara Beige.

• Trapezoidal plate covering the left and right quarters of the body. Hangs from abdomen armor that wraps around the abb section with the rear straps behind the thermal det
• The left rear strap features three “hose fitting” greeblies.
• The right rear strap features small oiler-style pouch.
• Hip-plates are tan with moderate weathering.
  

• Armour base color is Sahara Beige.
• Plastezote is desired for the foam on the belt, however plastezote material style is acceptable. Plastic sheet for the armor on top.

• • Yugoslavian M49 - M56 SMG style ammo pouch or replica. Replica must be made from leather or leather-like material
  • Pouch is fitted with two straps.
    • Left strap is snapped to the underside of the abdomen.
    • Right strap lays between ab and chest plates, over the belt. Snaps to the upper right side of the abdomen, past the black groove.
      

• Fabric is a brown cotton canvas/duck cloth material.
• Breeches style that flare out to the sides like riding breeches above the knee and below the drop boxes.
• Breeches are moderately weathered.
  

• Breeches have the correct stitching lines and the diamond shape pattern on the inside of the knee area.
• Breeches have two vertical rows of lace holes with black laces that run from beneath the outside of the knee to the bottom of the leg.

• Cover Strips are raised as beveled with a added layer strip on top.
• Greaves close in the back.
• The trapezoid shin plate (sniper knee plate) is affixed to the left greave.
• The “T” shin plate is affixed to the right greave.
• A harness style buckle greeblie attached to the outside edge of the upper shin plate.
• A ski boot style buckle greeblie is attached to the outside edge of the lower shin plate.
• Straps extend from each buckle, and the inner side of the shin plate.
• The straps may have a gap in the back of the shin or extend around the shin in one piece.
• Shins are tan with moderate weathering.
  

• The boot is Orca Bay Brecon Chelsea style.
• Similar matching style brown boots are acceptable.
• The boots should be weathered.
  

• Boots must be Orca Bay Brecon Chelsea Boots (Havana, Sand or Elk all acceptable when weathered correctly).

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

• Based on a real or replica Sterling sub-machine gun, scratch-built, cast, 3D print or a modified commercial toy Stormtrooper blaster.
• Tactical flashlight (Surefire scout M300 or replica) mounted on right side of barrel.
• Magazine is extended length.
• Power cylinder is larger with 2 outer cylinders and 2 smaller central cylinder
• Scope is a M38 1943 version.
• Scope rail can be fitted with rail blocks and a middle rail support block is optional.
  

• Base is based on S&T Airsoft sterling with closed working parts (no spring)
• Screws used are M4 x 25mm Allen screw/bolts and sunken Allen screws for power cylinders.

• Based on a real or replica Sterling sub-machine gun, scratch-built, cast, 3D print or a modified commercial toy Stormtrooper blaster. It has a extended stock attached at the rear and a extended front housing with second lower barrel.
• Tactical flashlight (Surefire scout M300 or replica) mounted on right side of barrel.
• Magazine is extended length.
• Power cylinder is larger with 2 outer cylinders and 2 smaller central cylinders
• Scope is a M38 1943 version
• Scope rail is fitted onto rail blocks, one inside the rear sight and the other at the front end of the rail.
• There are 3 swivel studs fitted, one on the rear stock and one each side of the front barrel housing.
• Sling is 25mm webbing strap that is adjustable using a silver 25mm 3 fixed bar webbing buckle (optional).
• Sling is fitted with Talon quick release 25mm swivel or replica (optional).
• Red lights fitted on both sides of the rear housing, Hengstler fitted with a red light for the 3 forward tubes and 2 small red lights fitted into the rear barrel housing under the torch, the lights are permanent and are non flashing or pulsed (optional hero version only).
  

• Base is based on S&T Airsoft sterling with closed working parts (no spring)
• Screws used are M4 x 25mm Allen screw/bolts and sunken Allen screws for power cylinders
• Sling is fitted with Talon quick release 25mm swivel.